Coming Back Soon

The Explorer is designed to be used in almost any setting. With its folding legs, it can be used at the beach, in rocky terrain, or at a more conve...

The Pioneer was designed for the outdoor man or woman on the go. Its sleek, two piece stake design allows you to take your Pioneer Campfire Grill a...

Specifically designed for pop ups. Video available Low pressure regulator with a side vent. The orientation of the vent is important when install...

This latch is found on units where the access door lock sits to the side of the door. This latch style is always found on access doors that swing o...

This wrap lamp was used on many units for many years. It forms a wrap around from the side to the front of the unit. It can be found on the pop up ...

End bracket for the roof brace 4800-4811. These brackets fit the the left hand and right hand ends of the 4800-4811 roof brace, and secure to the r...

Series 4100. 1/2 inch flared male fitting to 3/8 male. Measures 36 inches in length. Part number 4737-8871

Mounted to the rear of the trailer, this bracket mounts the power lift motor. Applicable to both round drive and square drive lift motors. Part num...

Specifically designed for pop ups. Video available Low pressure auto changeover regulator with a rear vent. The orientation of the vent is import...

This wrap lens was used on many units for many years. It forms a wrap around from the side to the rear of the unit. It can be found on the pop up b...

Safety latch to lock the lift system in early Coleman pop up campers. This catch is typically attached to the front or rear of the unit and catches...

The screen door track installs at the ceiling and the sliders hang the screen door when not in use. The final image shows an example of the screen ...

This cap fits two corners. If you were to draw an X in the center of your roof, each end of each line of the X would reach to the same cap. Fits l...

The lift arm provides lift to the pop up. They are found in each corner of the camper. CSR / Curb Side Rear RSF / Road Side Front Videos availab...

This cap fits two corners. If you drew an X in the center of your roof, each end of each line of the X would reach to the same cap. Polar white. P...

Slider channel hardware kit for the bed support pole. This hardware kit replaces the pins and hardware on slotted slider support channels.   Video...

This cap fits two corners. If you drew an X in the center of your roof, each end of each line of the X would reach to the same cap. Polar white. P...

Replacement jack handle for the swing down jacks. Part number 4716-1951

Used behind electrical cable hatches, water fill hatches and more. Three seals are included in this set. Largest ring seal measures 3-1/2 inches at...

Diamond plate metal wheel well. Popular on Pioneer, Destiny and Americana series pop ups. Measurements included are of the wheel well body not the ...

Designed for most Coleman Fleetwood campers with ABS tops. This brace kit has a curved design to fit the plastic roofs that have experienced saggin...

These bulbs will replace most of the interior lamps in units from the 1970's to the mid 1990's. This bulb pushes in a round socket, and twist to lo...

Installation kit for roof vents. Installs 14 inch by 14 inch roof vents. Comes with putty tape and 24 screws. Part number 4609-2421

The J-hook kit holds down the 20 lb LP gas bottles on the front of the pop up.  Comes with 2 J hooks, washers, and wing nuts. Measures 16-3/8 inche...

Mounts to the underside of the table, the table legs pivot on the nylon roller. This bracket will work with other designs that had different mounti...

Mounts to the underside of the table, the table legs pivot on the nylon roller. This bracket will work with other designs that had different mounti...

The crank shaft bushing is found a the rear of ratchet and clutch crank assemblies. it supports the rear of the drive shaft. Inserts into a 1 inch ...

This is the crank assembly found in many 12 foot boxes that install at the left hand side of the bumper. A chain drives the 12 tooth gear from this...

On the top corners of the deck rails you can find these corner brackets. They stack on top of each other, and close the 4 corners of the top rails....

Found on units built before 1997 that use roller style bed rails. This pin in installed in the top deck rail, and acts as a stop for the wheels and...

The duck bill attaches to the ceiling end of the shepherds hook, or tent support pole. Sometimes the tip out or glide out pole uses this cap at the...

Comes with a cream 18 inch by 18 inch vinyl patch, and 1 FL. OZ. of high strength VLP. Part number VPKCREME

This kit rebuilds the most popular direct drive center mounted crank assemblies. Rebuilds 6311 and 3000 series systems. Features a 7-3/4 inch long ...

 4 caps to replace all the corners on your Coleman or Fleetwood roof.   We have sold out of our limited availability of these caps. Please sign bac...

Exterior metal roof cap. This cap hides the installation of the exterior roof brace for the hat bracket. Found on ABS roofs that had the curved AC ...