Cerca risultati per 'tent support bracket'

The screen door storage bracket is used to secure the screen door in stored position for closing. This style has pins that accept to the bottom fra...

Mounting bracket for roof mounted crossbar braces. This bracket installs on the inside of the roof. Designed for 1996-2004 aluminum roofs   Measur...

Replacement base kit for the Dometic Trim Line awning rafter poles. These brackets can be installed to the roof for an original look, or to the bot...

Designed for metal and filon roofs. This bracket kit is for units produced through 1980 to the 2000's. Video available Found in the following AC ...

Metal corner trim angle bracket. Fits road side front and curb side rear. Black. Series 4228 Measures 12 inches in length on the long side, 8-3/4 i...

This inner reinforcing bracket bolts to the floor and top rails, providing structural stability. Measures 18-7/8  inches tall, by 4 inches wide on ...

This is the pole that stabilizes the bed. Two are found under each bed frame in these series. When the bed is pulled out, the pole swings down to t...

Use this kit to make small repairs to the tenting on your camper. Comes with a wide range of colors for both canvas and vinyl. Patches can be sewn ...

This stop bracket is installed at the ends of the top deck on the sides. One or two can be found at the front bed, and at the rear bed. The mountin...

Used to secure the awning from the camper to the awning lead rail. Tent support tip accepts into the end of the awning lead rail. The crutch cap re...

This mounting bracket kit is for the LP cover on the 1996 Grand tour series pop ups. Comes with a black angle bracket that measures 5-3/4 inches wi...

Found at the front corner of the glide out, or nearest the tongue. Series 3378 and 3395 Measures 27-1/2 inches long, by 1-3/8 X 1-3/4 inches. Part ...

Rear support bracket for the spare tire.  Popular on 2000's Grand Tour series units. Measures 23-3/4 inches tall by 6-1/8 inches wide. Part number ...

Found on units produced after 1997. This bracket rivets to the sides of the bed frame, and mounts the bed roller through the center hole. Here is a...

Left hand and right hand table top braces. These braces install at the dinette system to covert it into a bed. Light beige in color. Two braces are...

Swing bracket for the corner hutch in Plantation series units built through the 1980's. Removed from a 1986 Savannah. Measures 15 inches wide, 3 in...

Series 3300 Measures 3-1/4 inches long by 3/4 of an inch wide. Part number 4755-2111

Right angle bracket. Measures 6 inches by 1-1/2 inches by 3/4 inches. Part number 4741-221

Mounting bracket for the thermostat. Located behind the plastic base that the thermostat is installed into. This bracket mount it to the inside of ...

Black zinc plated 7 way plug bracket.16 gauge steel and piloted to mount a wide range of connectors. Measures 3-1/2 inches tall by 3-1/8 inches wid...

Storage bracket for the vanity mate system. Measures 1 inch tall with a 2-1/2 inch wide base. Part number 4757-0121

Rear support bracket for the spare tire. Popular on Destiny series units. Measures 23-1/2 inches tall by 6 inches wide. Studs measure 6-1/4 inches ...

Lower support side bracket for swing style doors. Series 3000. Measures 2-5/8 inches wide by 1 inch by 1 inch. Part number 4749B1278-USED

Mounting bracket to hold the shower wand. Installs in the shower stall or exterior shower compartment. Measures 2 inches at the base and 1-3/4 inch...