Complete set of wheel bearings. One kit services one wheel.
Kit comes complete with inner outer bearings and races, dust cap, seal and cotter pin. The inner and outer bearings and races in this kit are both the same size.
Fits most axles up to 2200lb, and have 1-1/16th smooth spindles.
There are a few easy ways to determine your correct bearing kit. Check your spindle or existing bearing sizes, or You can check your parts book for the installed axle. Directly matched axles for this bearing and seal kit are listed below.
You can also call us to help confirm your parts as well.
Part number 4716-1101
Fits the following axles...
4741G6301
4760-0011
4749-6071
4756A1101
4741E6301
4741G5761
4702-0781
4730M3011
4730L3011
4755-4441
4755A4441
4755C4441
4755D4441
4701-2881
4701B2881
4701G2881
Customer Reviews
Overall rating: 4.7 / 5 from 36 reviews.
Fits fine on our 94 Coleman Roanoke. Not a difficult job to install.
Unfortunatly these did not work for me. Only one bearing in each of the two kits I bought matched my 91 Coleman Plantation. Each wheel also had a larger bearing which I had to reuse. I think I need something similar to this image which I found on another website.
I downloaded the parts manual for my pop-up from their website, but called the store just in case to make sure I got the right part, they were very helpful. Thanks for the great service.
The kit was perfect except the AXLE dust seals (not dust caps) were too small to fit over the inner larger diameter of the axle. Fortunately my old ones were in very good repair so I was able to use them, without that I would not have been able to get the drum back on the axle. I have a 2002 Coleman Taos pop up. Everything about the kit otherwise was perfect and timely delivered.
I purchased this kit to keep in my truck just in case. I'm that kind of camper and my pop up is 25 years old. You guys are always spot on and reliable. I recommend you highly. Take care.
Exactly what I needed. I called and they looked my camper up for me. I had some parts in the kit I didn't need but better to have things I don't need then buy more stuff. Since this was the first time I had done this I wasn't sure what I would need. They are very helpful. Great videos.
Works great but had to order different seals. There was a warning on their website that some axles use different seals so it wasn't a total surprise. The original bearings were made in Romania, these ones are Chinese but that doesn't mean they are low quality. Time will tell .
This kit was perfect for our 1995 Coleman Destiny Royale. I also bought the thinner grease seals mentioned on the website page (that some models with idler hubs needed). While our popup does have idler hubs we did not need those thinner grease seals. The ones in the kit were the correct ones.
I searched for these bearing kits locally here in California for our 1987 Coleman Colorado. When I spoke to your parts department the representative knew exactly what I needed. The kits came in a timely manner and were just what was needed. Now we can take our trip to Montana with confidence! Thank you...
This worked well—note that you will need a brass drift punch to remove the old races and install the new ones. That was the most difficult part. This kit comes with wide all rubber rear seals. My ‘99 Sea Pine with a 7 1/2” Dexter axle needed the alternate narrower hybrid metal and rubber seals (despite the part number matching the kit with the wide rubber seals).
Works as intended but the universal seals were too large for my 1995 Coleman Fleetwood Williamsburg. I purchased the seals (as instructed on check out) by Coleman Pop Up parts..and it was an easy swap out. Thank you!
Your company is great! When I've had to call, the person was friendly and very helpful. I appreciate your prompt shipping and reasonable prices. Excellent service!
Exactly what I needed for my 1992 Coleman Pioneer Newport. This product gave me peace of mind while on my first big trip to NC with the camper. If ordering purchase the seals suggested as the ones in the kit are too large for some campers install was simple. Will purchase again if needed.
Bearing set was delivered as a advertised and has been installed. Performance will be measured in a couple of weeks when we take 1200
mike road trip from California to the Rockies. Hopefully performance will match ordering and delivery performance.
Bought two sets to replace both sides on a 1999 Fleetwood Taos. Kits were great and fit perfectly, with the exception of the new caps which were a bit too tight. I ended up re-using the old ones for now, but mainly just needed the bearings so super happy with the whole kit overall.
Customer service is most excellent. I ordered the wrong parts but didn't discover that until 2 months later, I had not tried to install the parts I mis-ordered, so I received an RMA and the correct were then ordered.
Thanks
The bearings & outer races were right, but the bearing seals were totally wrong. They were 2x's thicker than original (3/8" thick vs 3//16" thick) and the big problem was the ID was 1.0" and they needed to be 1.5" ID. So they did NOT work. They could not be made to work. So I had to seek different seals.
